|
Example of Juniper SSG Configuration
set clock ntp
set clock timezone -6
set vrouter trust-vr sharable
set vrouter "untrust-vr"
exit
set vrouter "trust-vr"
unset auto-route-export
exit
set service "RDC" protocol tcp src-port 0-65535 dst-port 3389-3389
set service "pcAnywhere1" protocol tcp src-port 0-65535 dst-port 5631-5632
set service "pcAnywhere1" + udp src-port 0-65535 dst-port 5631-5632
set service "Upluad" protocol tcp src-port 0-65535 dst-port 85-85
set service "IP5060" protocol tcp src-port 0-65535 dst-port 5060-5060
set service "IP5061" protocol tcp src-port 0-65535 dst-port 5061-5061
unset alg sip enable
set auth-server "Local" id 0
set auth-server "Local" server-name "Local"
set auth default auth server "Local"
set auth radius accounting port 1646
set admin name "admin"
set admin port 8080
set admin auth timeout 10
set admin auth server "Local"
set admin format dos
set zone "Trust" vrouter "trust-vr"
set zone "Untrust" vrouter "trust-vr"
set zone "DMZ" vrouter "trust-vr"
set zone "VLAN" vrouter "trust-vr"
set zone "Untrust-Tun" vrouter "trust-vr"
set zone "Trust" tcp-rst
set zone "Untrust" block
unset zone "Untrust" tcp-rst
set zone "DMZ" tcp-rst
set zone "VLAN" block
unset zone "VLAN" tcp-rst
set zone "Untrust" screen tear-drop
set zone "Untrust" screen syn-flood
set zone "Untrust" screen ping-death
set zone "Untrust" screen ip-filter-src
set zone "Untrust" screen land
set zone "V1-Untrust" screen tear-drop
set zone "V1-Untrust" screen syn-flood
set zone "V1-Untrust" screen ping-death
set zone "V1-Untrust" screen ip-filter-src
set zone "V1-Untrust" screen land
set interface "ethernet0/0" zone "Untrust"
set interface "ethernet0/1" zone "DMZ"
set interface "bgroup0" zone "Trust"
set interface bgroup0 port ethernet0/2
set interface bgroup0 port ethernet0/3
set interface bgroup0 port ethernet0/4
set interface bgroup0 port ethernet0/5
set interface bgroup0 port ethernet0/6
unset interface vlan1 ip
set interface ethernet0/0 ip 192.168.11.61/30
set interface ethernet0/0 route
set interface ethernet0/1 ip 172.16.10.1/16
set interface ethernet0/1 nat
set interface bgroup0 ip 10.10.10.1/24
set interface bgroup0 nat
unset interface vlan1 bypass-others-ipsec
unset interface vlan1 bypass-non-ip
set interface ethernet0/0 ip manageable
set interface ethernet0/1 ip manageable
set interface bgroup0 ip manageable
set interface ethernet0/0 manage ping
set interface ethernet0/0 manage ssh
set interface ethernet0/0 manage ssl
set interface ethernet0/0 manage mtrace
set interface bgroup0 manage mtrace
set interface ethernet0/0 vip untrust 3389 "RDC" 10.10.10.10
set interface ethernet0/0 vip untrust 85 "Upluad" 10.10.10.10
set interface ethernet0/0 vip untrust 5631 "pcAnywhere1" 10.10.10.10
set interface ethernet0/0 vip untrust 80 "HTTP" 10.10.10.10
set interface ethernet0/0 vip untrust 5060 "IP5060" 10.10.10.176
set interface ethernet0/0 vip untrust 5061 "IP5061" 10.10.10.169
set interface bgroup0 dhcp server service
set interface bgroup0 dhcp server auto
set interface bgroup0 dhcp server option domainname chicagotech.net
set interface bgroup0 dhcp server option dns1 4.2.2.1
set interface bgroup0 dhcp server option dns2 4.2.2.1
set interface bgroup0 dhcp server ip 10.10.10.11 to 10.10.10.200
unset interface bgroup0 dhcp server config next-server-ip
set interface "serial0/0" modem settings "USR" init "AT&F"
set interface "serial0/0" modem settings "USR" active
set interface "serial0/0" modem speed 115200
set interface "serial0/0" modem retry 3
set interface "serial0/0" modem interval 10
set interface "serial0/0" modem idle-time 10
set flow tcp-mss
unset flow tcp-syn-check
set domain chicagotech.net
set pki authority default scep mode "auto"
set pki x509 default cert-path partial
set address "Trust" "0.0.0.0/0" 0.0.0.0 0.0.0.0
set address "Trust" "10.10.10.10/24" 10.10.10.10 255.255.255.0
set address "Trust" "10.10.10.10/255.255.255.255" 10.10.10.10
255.255.255.255
set address "Trust" "10.10.10.10/32" 10.10.10.10 255.255.255.255
set address "Trust" "phone ip1" 10.10.10.169 255.255.255.255
set address "Trust" "phone ip2" 10.10.10.176 255.255.255.255
set group address "Trust" "phone ips"
set group address "Trust" "phone ips" add "phone ip1"
set group address "Trust" "phone ips" add "phone ip2"
set ike respond-bad-spi 1
unset ike ikeid-enumeration
unset ike dos-protection
unset ipsec access-session enable
set ipsec access-session maximum 5000
set ipsec access-session upper-threshold 0
set ipsec access-session lower-threshold 0
set ipsec access-session dead-p2-sa-timeout 0
unset ipsec access-session log-error
unset ipsec access-session info-exch-connected
unset ipsec access-session use-error-log
set url protocol websense
exit
set policy id 13 from "Trust" to "Untrust" "phone ips" "Any" "ANY" permit
log traffic priority 0
set policy id 13
exit
set policy id 7 from "Untrust" to "Trust" "Any" "VIP(ethernet0/0)" "RDC"
permit log
set policy id 7
exit
set policy id 5 from "Untrust" to "Trust" "Any" "0.0.0.0/0" "MGCP" permit
set policy id 5
exit
set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit
set policy id 1
exit
set policy id 8 name "pcAnywhere" from "Untrust" to "Trust" "Any"
"VIP(ethernet0/0)" "pcAnywhere1" permit
set policy id 8
exit
set policy id 9 name "Upload" from "Untrust" to "Trust" "Any"
"VIP(ethernet0/0)" "Upluad" permit
set policy id 9
exit
set policy id 10 name "http" from "Untrust" to "Trust" "Any"
"VIP(ethernet0/0)" "HTTP" permit
set policy id 10
exit
set policy id 11 name "IPPhone" from "Untrust" to "Trust" "Any"
"VIP(ethernet0/0)" "IP5060" permit
set policy id 11
exit
set policy id 12 name "IP5061" from "Untrust" to "Trust" "Any"
"VIP(ethernet0/0)" "IP5061" permit
set policy id 12
exit
set nsmgmt bulkcli reboot-timeout 60
set ssh version v2
set config lock timeout 5
set ntp server "0.0.0.0"
set ntp server backup1 "0.0.0.0"
set ntp server backup2 "0.0.0.0"
set snmp port listen 161
set snmp port trap 162
set vrouter "untrust-vr"
exit
set vrouter "trust-vr"
unset add-default-route
set route 0.0.0.0/0 interface ethernet0/0 gateway 192.168.11.62 preference
20
exit
set vrouter "untrust-vr"
exit
set vrouter "trust-vr"
exit
Post your questions, comments, feedbacks and suggestions
Contact a consultant
Related Topics
|
